Find Led Wired Road Stud, Plastic Wired Road Stud, Tunnel Traffic Road Stud on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Road Stud > Customized Led Road Stud > markers light Tunnel plastic led wired road stud

markers light Tunnel plastic led wired road stud

Basic Info

Model No.: WDM-RC24-2-RY

Product Description

markers light Tunnel plastic led wired road stud
1. Detailed parameters of markers light Tunnel plastic led wired road stud:
1. Product model: WDM-DD07-PC
2. Product size: 100*105*19MM
3. Lamp bead color: yellow and white
4. Number of lamp beads: 12
6. Yellow wavelength: 590-595NM
9. White brightness: 18900-22600MCD
10. Protection grade: IP68
11. Shell material: plastic
12. Working voltage: DC12V/24V
13. Rated power: 0.5W
14. Working temperature: -40℃~60℃

15. Working mode: Chang Liang

Tunnel plastic road stud-1

Overview of the markers light Tunnel plastic led wired road stud:

The tunnel active stud is a kind of road stud. It is set along both sides of the road and is used to indicate the road and the edge of the tunnel at night or in rain and fog. It consists of a housing, LEDs, wires, and control devices. It can use solar panels It can be powered by alternating current. It can rely solely on active lighting and can be combined with passive reflective visual induction facilities. The working mode is always on or flashing. The active road studs used in tunnels have oil resistance requirements and require a large number of LEDs. The housing can be a plastic housing. The active road stud shell used for pavement has pressure resistance requirements, and it is mostly a cast aluminum shell, which combines active light emission with reflective light.

Tunnel plastic road stud-3

The characteristics of the markers light Tunnel plastic led wired road stud:
1. Plastic active road studs are a type of road studs that are set along both sides of the tunnel and are used to indicate road and tunnel edges at night or in rain and fog.
2. The plastic active road studs use ultra-bright Taiwan wafer chip lamp beads. The color is eye-catching and the color is clear. It has good visual performance, which can attract the attention of the driver, reduce the speed, and improve the driving safety on the road.
3. There are many colors for plastic active spikes, and the color of the lamp beads can be customized according to customer requirements.

4. Plastic active road studs have good waterproof and dustproof effects, and the protection grade can reach IP68.

Tunnel plastic road stud-04

The installation steps of the markers light Tunnel plastic led wired road stud:
(1) The tunnel active studs are generally installed on the side wall of the tunnel cable trench. The installation position is first determined with a ruler. The height is designed according to the drawing to ensure that the longitudinal direction is on a straight line, and the horizontal and horizontal alignment is at the same time. Position holes on both sides of the active spike, drill holes, and plunge the rubber plug into the drilled holes. The middle of the two holes is drilled through the wall hole? 8 or? 10 according to the diameter of the active spike.
(2) The ratio of glue is 1: 0.7 for glue A and glue B, then add 15%-30% of cement as filler (the glue is not easy to stir too much at one time, enough for one person to stick 50-70 spikes) glue). The colloid should be stirred evenly (the hand drill is equipped with a stirrer) and the color is consistent. Each active spike requires about 30-40 grams of glue.
(3) The surface of the installation location should be cleaned. Use a batch knife of about 30-40 grams of glue and apply it to the back of the spike. Put the active spike wire through the side wall of the cable trench (pre-punched holes) and place it At the location, install self-tapping and tighten with a Phillips screwdriver on both sides.
(4) After installing the road studs, scrape the glue around the road studs with a batch knife to clean them up.
(5) After the installation of the road studs, after receiving the pre-arranged main line, connect the control box and test whether there is a short circuit with a universal meter. If there is no problem, you can connect the main power.
Precautions:

Do not touch the vicinity of the lamp with your hands. Avoid glue sticking to the housing and affecting the luminous effect! It is forbidden to install active spikes with water, moisture and oil stains (easy to fall off). 4 hours after installation, evacuate the road cone.

Tunnel plastic road stud-05

Field application pictures of markers light Tunnel plastic led wired road stud:

Tunnel plastic road stud-09

In addition for the markers light Tunnel plastic led wired road stud,we also do other solar road stud:

Solar Warning Flashing Sign
Solar Safety Signs
Solar Warning Sign
Solar Traffic Road Sign
Road Stud Reflectors
Garden Solar Road Stud

Contact us if you need more details on Led Wired Road Stud. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Plastic Wired Road Stud、Tunnel Traffic Road Stud. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Road Stud > Customized Led Road Stud